Robobrew/BrewZilla V3 All Grain Brewing System With Pump - 35L/9.25G - 220v

(No reviews yet) Write a Review
$469.99
Shipping:
Calculated at Checkout

Product Overview

Robobrew/BrewZilla V3.1 All Grain Brewing System With Pump - 35L/9.25G 220v

 

The Robobrew is an all-in-one electric brewing system that has built-in elements for heating and boiling, programmable mash schedule and delayed start, a built-in pump for recirculation, an onboard water resistant control panel for setting and monitoring temperatures, a removable grain basket, and a built-in spigot for transferring. This more powerful version of the Robobrew requires 220V power.

 

The V3.1.1 unit features an upgraded main circuit board that changes how the automatic step mashing functions. Now when moving from step to step, the timer for each step will not begin counting down until the programmed temperature is reached. This means more accurate mash schedules than ever before! The new board also introduces boil addition timers so you'll never miss the mark for hop additions.

 

Automatic Step Mashing! 
One of the coolest features of the Robobrew is the ability to program the unit with up to 6 individual temperatures and durations so you can step mash precisely how you desire. Simply press the "S1-S6" button to select the stage you want to adjust, and use the temp, time and +/- buttons to program the stage. If you have less than 6 stages in your mash schedule, program the stages you want to skip with 00:00 as the time and the controller will automatically move on to the next step. When all the stages are complete, the Robobrew will sound an alarm and hold the last set temperature.

 

The programmable stages can also be used to set a delayed start of up to 23 hours in advance so that you can have your water hot and ready to go when you get home from work or wake up in the morning. In order to do this, fill the unit with strike water and program the controller with two steps. Step 1 should be programmed at a temperature lower than the unheated strike water (so the elements will remain off), and the duration should be programmed for however long you want the delay. Then program Step 2 with your desired strike water temperature and a duration of 1-2 hours, giving the Robobrew ample time to heat up and giving you a margin of error in case you hit the snooze button the morning of brew day.

 

Built-in magnetic drive pump to easily recirculate the wort during the mash. We recommend getting some silicone tubing to go with the recirculation arm. This allows you more control over the recirculation and you can then use the pump to transfer your wort to your fermenter. As with any mash, be sure to stir your grain very thoroughly after mashing-in so you start out with an even temperature throughout the grain bed.

 

Dual heating elements run off of a single 220 volt plug and have individual switches allowing for more control over the heating process. One element is 1900 watts and the other is 500 for a combined 2400 watts! Use both when you need to ramp up the temperature quickly either at the start to get to your mash temp or to go from your mash temp to boiling. Use only one of the elements when you want to hold a temperature.

Features:

  • Gen 3.1.1
  • Stainless steel construction
  • 9 gallon total capacity with a finished beer output of 5-6 gallons
  • Digital temperature controller
  • Automatic step mashing with 6 programmable stages
  • 220V power
  • NEMA 6-30R plug
  • Dual heating elements for total control (1900 watts and 500 watts)
  • Stainless steel 1/2 in ball valve for draining (don't have to use the pump)
  • Immersion wort chiller included
  • Stainless steel malt pipe/basket
  • Stamped volume markers
  • Glass lid
  • Magnetic drive pump for recirculation
  • Recirculation arm
  • Temperature reads in °F or °C (press and hold temp button for several seconds to adjust)
  • 32.75 in H (with recirculation arm) x 12.5 in D
  • Recommended max. grain bill - 18 lbs
  • Recommended min. grain bill - 8 lbs
  • You might also want:
  • 2' of 1/2" ID Silicone tubing for sparging and draining.
  • To connect includedchiller: 20' of 1/2" ID tubing, 3 small hose clamps and 1 brass Garden Hose Thread by 1/2" barb adaptor. 

This is a drop ship item - Please allow additional time for shipping

 

Reviews

(No reviews yet) Write a Review